Manufacturer
Pro Clima Roflex 50, pipe sleeves for indoors and outdoors, Ø 50 -90 mm
For the quick and permanently tight passage of pipes through the airtight layer. Can also be used outdoors, e.g. for under-roofing or renovation vapour barriers.Bonding with TESCON VANA.Application video Data sheet Application instructionsAdvantagesKeeps components dry: quick and easy sealingSecure connection thanks to TESCON VANA with waterproof SOLID adhesiveSafe even in hot environments: temperature-stable up to 150 °CPractical working: Pipes can be pushed and pulled in the sleeve - the connection remains tightExtremely flexible and stretchable, no protruding grommetStandard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2Best values in the pollutant test, test carried out in accordance with AgBB / ISO 16000SubstratesClean substrates before bonding.Bonding is not possible on frozen substrates. There must be no repellent substances on the materials to be bonded (e.g. greases or silicones). Substrates must be sufficiently dry and stable.Permanent bonding is achieved on all pro clima interior and exterior membranes, other vapour barrier and airtight membranes (e.g. made of PE, PA, PP and aluminium) or sarking/sarking membranes and wall formwork membranes (e.g. made of PP and PET).Bonding and connections can be made on planed and painted wood, hard plastics or metal (e.g. pipes, windows, etc.), hard wood-based panels (chipboard, OSB and BFU, MDF and wood fibre underlay boards).Pre-treatment with TESCON PRIMER is required when bonding wood fibre underlay boards or on smooth, mineral substrates. Concrete or plaster substrates must not sand.The best results for the safety of the construction are achieved on high-quality substrates.You are responsible for checking the suitability of the substrate; test bonding may be recommended.Pre-treatment with TESCON PRIMER is recommended for non-load-bearing substrates.General conditionsAdhesive bonds must not be subjected to tensile loads.Rub adhesive tapes firmly. Ensure sufficient counter pressure.Windproof, airtight or rainproof bonds can only be achieved on vapour control layers or sarking and façade membranes laid without folds.Quickly remove increased room humidity through consistent and constant ventilation, if necessary set up a building dryer.
€3.59*
Pro Clima, Contega PV, vapour-retarding plaster connection tape with reinforcement fabric, roll 15 m, width 200 mm
Advantages- Saves time: no plaster reinforcement required- Defined transition between vapour barrier and plaster- Secure connection: Reinforcing mesh increases the stability of the adjacent plaster substrate- Standard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2- Best values in the pollutant test, test carried out in accordance with AgBB / ISO 16000Data sheet Processing instructionsApplicationFor defined cross-trade connections of membranes or wood-based panels to components to be plastered (masonry or concrete).General conditionsAdhesive bonds must not be subjected to tensile loads.Apply adhesive tapes firmly. Ensure sufficient counter pressure.Airtight bonding can only be achieved by installing the connecting tape without creases and without interruption.Quickly dissipate increased room humidity through consistent and constant ventilation, if necessary set up a building dryer.When plastering, please follow the plaster manufacturer's recommendations for non-absorbent substrates. A bonding bridge may be required.If the airtight connection is only made after plastering, moisture may enter the thermal insulation or disrupt the construction process.CONTEGA PV minimises this problem.SubstratesClean substrates before bonding.Bonding is not possible on frozen substrates. There must be no repellent substances on the materials to be bonded (e.g. grease or silicone). Remove peeling old coatings or similar. Substrates must be sufficiently dry and stable.Permanent bonding is achieved on all pro clima inner membranes and other vapour control layers and airtight membranes (e.g. made of PE, PA, PP and aluminium).Bonding can be carried out on planed and painted wood, hard plastics, hard wood-based panels (chipboard, OSB and BFU boards).The PET fleece can be embedded in the plaster centre layer on all plasterable substrates such as brick, sand-lime brick, aerated concrete, pumice, concrete, etc.Use ORCON F for bonding to masonry, concrete or rough substrates.The best results for the safety of the construction are achieved on high-quality substrates.You are responsible for checking the suitability of the substrate; test bonding may be recommended.Pre-treatment with TESCON PRIMER is recommended for non-load-bearing substrates.
Content: 15 Linear metre (€2.75 / 1 Linear metre)
€41.20*
Pro Clima, Instaabox, installation box, for up to 3 appliance boxes
AdvantagesFor cables and conduits up to 20 mm in diameterStandard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2Provides space for up to three appliance boxesCan be extended as required: Simply cut open and glue togetherBest values in the pollutant test, test carried out in accordance with AgBB / ISO 16000Data sheet Processing instructionsMaterial: stretchable, flexible polyethyleneTemperature resistance -10°C to +80°CCable diameter up to 20 mmsd value >10 mDepth 55 mmLength/width of installation level 260 mm/ 130 mmTotal length/width 320 mm/ 190 mmApplicationIn constructions without an installation level, the INSTAABOX can create space for appliance boxes or similar. For this purpose, it is attached to the existing vapour barrier and airtight layer and connected to it in an airtight manner. The requirements of DIN 4108-7, SIA 180 and OENORM B 8110-2 are met with regard to airtightness when using conventional appliance boxes. The INSTAABOX can be used for both interior and exterior walls.The INSTAABOX is oversized so that the airtightness level is not damaged when the openings for the appliance boxes are drilled out.General conditionsBonded joints must not be subjected to tensile loads. When bonding vapour barriers, battens must support the weight of the insulation material. Secure bonding with battens if necessary.Rub adhesive tapes down firmly. Ensure sufficient counter pressure. Airtight bonding can only be achieved on vapour control layers that are laid without folds.Quickly remove increased room humidity through consistent and constant ventilation, if necessary set up a building dryer.SubstratesThe INSTAABOX can be combined with all standard airtight substrates. Recommendations for suitable fasteners for connection to the airtight layer (e.g. vapour barrier,
€3.20*
Pro Clima, INTELLO PLUS, reinforced hydrosafe® high-performance vapour control layer for all fibrous insulation materials, 50 m
ApplicationFor use in roofs, walls, ceilings and floors in externally vapour-permeable and vapour-tight constructions, e.g. flat/slope roofs and green roofs according to design.Data sheet Processing instructions Safety data sheet Passive house certificate Video Functionality Application videoAdvantagesBest protection against structural damage and mould because it is moisture-variable with more than 100-fold spreadTest winner at Stiftung Warentest 4/2012Permanently safe: function officially tested and confirmed (ETA-18/1146)Safe winter construction sites thanks to Hydrosafe® functionCan be combined with all fibre-based insulation materials (including blown-in insulation)Easy to process: Dimensionally stable, no splicing or tearingBest values in the pollutant test, test carried out in accordance with AgBB / ISO 16000Processingpro clima INTELLO PLUS should be laid with the foil side (labelling) facing the installer. They can be laid tightly and without sagging along and across the supporting structure, e.g. the rafters. When laid horizontally (across the supporting structure), the distance from the supporting structure is limited to a maximum of 100 cm. After installation, the weight of the insulation material must be supported on the inside by transverse battens at a maximum distance of 50 cm. If, when using mat and board-shaped insulating materials, the weight of the insulating material, for example, is expected to exert planned tensile loads on the adhesive tape joints, an additional support batten should be placed on the overlap bonding. Alternatively, the adhesive tape can be additionally secured on the overlap with transverse adhesive tape strips at 30 cm intervals.Airtight bonding can only be achieved on vapour control layers laid without folds. Quickly dissipate increased room humidity (e.g. during the construction phase) through consistent and constant ventilation. Occasional shock ventilation is not sufficient to quickly remove large amounts of building-related moisture from the building; if necessary, install a building dryer.To prevent condensation, INTELLO PLUS should be airtightly bonded immediately after installation of the mat and board-shaped thermal insulation. This is particularly important when working in winter.Additionally for blow-in insulation materialsINTELLO PLUS can also be used as a boundary layer for all types of blown-in insulation materials. Its reinforcing fabric ensures low expansion during blowing. Laying along the supporting structure offers the advantage that the butt joint is on a solid base and is therefore protected.To avoid condensation, the blown-in insulation should be installed immediately after completion of the airtight layer. This is particularly important when working in winter.The functional principleMaximum protection against structural damage and mouldINTELLO works according to the principle of a climate-controlled membrane: in winter it is sealed against moisture, in summer the molecular structure becomes more open and enables safe drying out.
Content: 75 Square metre (€4.21 / 1 Square metre)
€315.95*
Pro Clima, KAFLEX duo cable sleeves for 2 cables, Ø 4.8 - 12 mm, inside and outside
For fast and permanently tight cable entry through the airtight layer. Can also be used outdoors, e.g. for under-roofing or renovation vapour barriers.Data sheet Processing instructions Processing videoAdvantagesKeeps building components dry: quick and easy sealingSecure connection thanks to waterproof SOLID adhesivePractical working: Cables can be pushed and pulled in the sleeve - the connection remains tightExtremely flexible and stretchable, no protruding grommetMore flexible further work: Can be exposed to the weather for 6 monthsStandard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2Best values in the pollutant test, test carried out in accordance with AgBB / ISO 16000SubstratesClean substrates before bonding.Bonding is not possible on frozen substrates. There must be no repellent substances on the materials to be bonded (e.g. greases or silicones). Substrates must be sufficiently dry and stable.Permanent bonding is achieved on all pro clima interior and exterior membranes, other vapour barrier and airtight membranes (e.g. made of PE, PA, PP and aluminium) or sarking/sarking membranes and wall formwork membranes (e.g. made of PP and PET).Bonding and connections can be made on planed and painted wood, hard plastics or metal (e.g. pipes, windows, etc.), hard wood-based panels (chipboard, OSB and BFU, MDF and wood fibre underlay boards).Pre-treatment with TESCON PRIMER is required when bonding wood fibre underlay boards or on smooth, mineral substrates. Concrete or plaster substrates must not sand.The best results for the safety of the construction are achieved on high-quality substrates.You are responsible for checking the suitability of the substrate; test bonding may be recommended.Pre-treatment with TESCON PRIMER is recommended for non-load-bearing substrates.General conditionsAdhesive bonds must not be subjected to tensile loads.Rub adhesive tapes firmly. Ensure sufficient counter pressure.Windproof, airtight or rainproof bonds can only be achieved on vapour control layers or sarking and façade membranes laid without folds.Quickly remove increased room humidity through consistent and constant ventilation, if necessary set up a building dryer.
€2.40*
Pro Clima, KAFLEX mono cable sleeves for 1 cable, Ø 4.8 - 12 mm, inside and outside
For fast and permanently tight cable entry through the airtight layer. Can also be used outdoors, e.g. for under-roofing or renovation vapour barriers.Data sheet Processing instructions Processing videoAdvantagesKeeps building components dry: quick and easy sealingSecure connection thanks to waterproof SOLID adhesivePractical working: Cables can be pushed and pulled in the sleeve - the connection remains tightExtremely flexible and stretchable, no protruding grommetMore flexible further work: Can be exposed to the weather for 6 monthsStandard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2Best values in the pollutant test, test carried out in accordance with AgBB / ISO 16000SubstratesClean substrates before bonding.Bonding is not possible on frozen substrates. There must be no repellent substances on the materials to be bonded (e.g. greases or silicones). Substrates must be sufficiently dry and stable.Permanent bonding is achieved on all pro clima interior and exterior membranes, other vapour barrier and airtight membranes (e.g. made of PE, PA, PP and aluminium) or sarking/sarking membranes and wall formwork membranes (e.g. made of PP and PET).Bonding and connections can be made on planed and painted wood, hard plastics or metal (e.g. pipes, windows, etc.), hard wood-based panels (chipboard, OSB and BFU, MDF and wood fibre underlay boards).Pre-treatment with TESCON PRIMER is required when bonding wood fibre underlay boards or on smooth, mineral substrates. Concrete or plaster substrates must not sand.The best results for the safety of the construction are achieved on high-quality substrates.You are responsible for checking the suitability of the substrate; test bonding may be recommended.Pre-treatment with TESCON PRIMER is recommended for non-load-bearing substrates.General conditionsAdhesive bonds must not be subjected to tensile loads.Rub adhesive tapes firmly. Ensure sufficient counter pressure.Windproof, airtight or rainproof bonds can only be achieved on vapour control layers or sarking and façade membranes laid without folds.Quickly remove increased room humidity through consistent and constant ventilation, if necessary set up a building dryer.
€2.20*
Pro Clima, ORCON F, all-round connection adhesive for indoors and outdoors, 310 ml cartridge
- Creation of airtight connections for all types of vapour control layers and airtight membranes. This includes all pro clima vapour control layers and airtight membranes (e.g. pro clima INTELLO, DB+, INTESANA, DASATOP and DA).Data sheet Processing instructions- Bonding windtight connections of all types of sarking and underlay membranes (PP, PET). The connection bonding of e.g. pro clima SOLITEX MENTO family, SOLITEX UD, SOLITEX PLUS and SOLITEX UM connect complies with the requirements of the ZVDH product data sheets.- Windproof bonding of wall formwork membranes (e.g. pro clima SOLITEX FRONTA family).- Bonding of overlaps and connections of trickle protection membranes.ApplicationCreation of airtight connections of all types of vapour control layers and airtight membranes. This includes all pro clima vapour control layers and airtight membranes (e.g. pro clima INTELLO, DB+, INTESANA, DASATOP and DA).Bonding windproof connections of all types of underlay and underlay membranes (PP, PET). The connection bonding of e.g. pro clima SOLITEX MENTO family, SOLITEX UD, SOLITEX PLUS and SOLITEX UM connect fulfils the requirements of the ZVDH product data sheets.Windproof bonding of wall formwork membranes (e.g. pro clima SOLITEX FRONTA family).Bonding of overlaps and connections of trickle protection membranes.AdvantagesBonds securely even in frost: can be applied from -10 °CParticularly durable: 100 years of adhesive strength independently tested and confirmedProvides a firm and permanently elastic holdEnsures secure connections: Penetrates deep into the substrate, remains elasticTest winner at Stiftung Warentest 4/2012Standard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2Can be stored down to -20 °C. Material does not freeze in the cartridgeBest values in the pollutant test, test carried out in accordance with AgBB / ISO 16000Consumption valuesDelivery form Contents Bead RangeCartridge 310 ml 5 mm ~ 15 mAdvantagesBonds securely even in frost: can be used from -10 °CParticularly durable: 100 years of adhesive strength independently tested and confirmedProvides a firm and permanently elastic holdEnsures secure connections: Penetrates deep into the substrate, remains elasticTest winner at Stiftung Warentest 4/2012Standard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2Can be stored down to -20 °C. Material does not freeze in the cartridgeBest values in the pollutant test, test carried out in accordance with AgBB / ISO 16000ApplicationCreation of airtight connections for all types of vapour control layers and airtight membranes. This includes all pro clima vapour control layers and airtight membranes (e.g. pro clima INTELLO, DB+, INTESANA, DASATOP and DA).Bonding windproof connections of all types of underlay and underlay membranes (PP, PET). The connection bonding of e.g. pro clima SOLITEX MENTO family, SOLITEX UD, SOLITEX PLUS and SOLITEX UM connect fulfils the requirements of the ZVDH product data sheets.Windproof bonding of wall formwork membranes (e.g. pro clima SOLITEX FRONTA family).Bonding of overlaps and connections of trickle protection membranes.General conditionsBonds must not be subjected to tensile loads.The final strength is only achieved when dry. This must be taken into account for subsequent airtightness measurements and/or the installation of blown-in insulation materials. If necessary, securing measures, e.g. mechanical securing of non-load-bearing substrates, are recommended.Quickly dissipate increased room humidity through consistent and constant ventilation, if necessary set up a building dryer.SubstratesClean substrates before bonding. Mineral surfaces (plaster or concrete) may be slightly damp.Bonding is not possible on frozen substrates. There must be no repellent substances on the materials to be bonded (e.g. grease or silicone). Substrates must have sufficient load-bearing capacity - if necessary, a mechanical securing device (pressure bar) must be used (e.g. for sanding substrates). Permanent bonding is achieved on all pro clima interior and exterior membranes, other vapour control layers and airtight membranes (e.g. made of PE, PA, PP and aluminium) or sarking/sarking membranes and wall formwork membranes (e.g. made of PP and PET).Connections can be made on mineral substrates (e.g. plaster or concrete), rough-sawn and planed wood as well as hard wood-based panels (chipboard, OSB, BFU, MDF).The best results for the safety of the construction are achieved on high-quality substrates.It is your own responsibility to check the suitability of the substrate; test bonding may be recommended.
Content: 0.315 Litre (€29.02 / 1 Litre)
€9.14*
Pro Clima, RB trickle protection membrane, roll 50 m
AdvantagesEasy to process: robust PP fleeceFlexible use: for dry and slightly damp fillsReliable protection against dust thanks to particularly dense weaveFor safe building components: Particularly open to diffusionData sheet Processing instructionsApplicationUsed as dust and trickle protection for rooms under suspended ceilings with fills and in floors.General conditionsThe pro clima RB trickle protection membrane retains dust and fibres and can be used on floors or under ceilings. The membrane is laid on a sufficiently pressure-resistant underlay that absorbs mechanical loads, e.g. from insulation materials, fills or other inserts. The trickle protection membrane itself must remain free of corresponding loads.If the membrane is installed on building components from below, the membrane must be mechanically secured. This can be provided either by cross battens (for lightweight materials such as mineral wool) or plate-shaped components that support the membrane over its entire surface (e.g. when using wood fibre or cellulose insulation or fills).Membrane joints must have an overlap of approx. 10 cm. The printed marking serves as a guide. If necessary, the overlaps can be bonded with adhesive tapes from the pro clima system (e.g. TESCON VANA all-round adhesive tape). When bonding, ensure sufficient contact pressure and counter pressure.Position the adhesive tape in the centre of the overlap and apply carefully, pull by pull, without load or creases. The PRESSFIX pressing aid enables even pressure to be applied.Connections to rough or mineral substrates can be created in the pro clima system using the ORCON F connection adhesive, for example. To do this, apply a bead of adhesive at least 5 mm thick (more if necessary for very rough surfaces) and lay the trickle protection membrane in the adhesive bed. Do not press the adhesive completely flat.The RB trickle protection membrane can also be combined with slightly damp fills when laying on a pressure-resistant base (e.g. floors or in joist compartments). Care must be taken to ensure that the moisture can dry out and that neighbouring materials are not damaged by the moisture.To protect the RB trickle protection membrane from mechanical damage and UV exposure, a full-surface covering must be provided. This panelling is not required in inaccessible rooms withoutLaying in the cavityLay the membrane in the cavity.Run up the sides of all rising components (e.g. ceiling beams) and fix with staples or nails.Overlap sheet joints by approx. 10 cm.Glue overlaps with TESCON VANA if necessary.
Content: 75 Square metre (€1.18 / 1 Square metre)
€88.49*
Pro Clima, SOLITEX FRONTA QUATTRO, wall formwork sheeting for gap formwork up to 35 mm, roll 50 m
Use as a wall formwork membrane behind closed and open façades (gap formwork, up to 35 mm gap width; formwork width = at least 3x gap width). Installation on formwork, wood-based panels and all matt and panel-shaped thermal insulation materials.Data sheet Processing instructionsAdvantagesEnsures secure building components: Highly permeable to diffusion and at the same time maximally impermeable to driving rainDry building components: non-porous TEEE functional membrane actively transports moisture to the outsideNot visible behind gap formwork: black fleece with print in the overlap areaMaximum ageing resistance and thermal stability thanks to TEEE membrane6 months outdoor weatheringGeneral conditionsSOLITEX FRONTA QUATTRO membranes must be laid with the printed side facing outwards. They are laid horizontally, tightly and without sagging.When used behind gap formwork, the gap size must not exceed 35 mm. The width of the formwork: min. 3x gap width.The distance between the gap formwork and the sheet must be at least 20 mm.Fixings must not be made in areas where water runs off collectively.Additional measures should be taken during the construction phase (e.g. tarpaulins) in the case of inhabited buildings or buildings requiring special protection. Tarpaulins should also be considered for longer interruptions to work.Moisture-active wind sealSOLITEX FRONTA QUATTRO wall formwork membranes are equipped with monolithic, non-porous, moisture-active functional membranes made of the latest TEEE technology.They offer significantly higher component safety than conventional microporous membranes.New standards: Monolithic SOLITEX membranepro clima SOLITEX FRONTA QUATTRO has a non-porous, closed-cell TEEE membrane that offers particularly good protection against driving rain.Unlike conventional wall formwork membranes, where diffusion takes place via air exchange through the microporous membrane, with a SOLITEX membrane diffusion takes place actively along the molecular chains.SOLITEX FRONTA QUATTRO has an sd value of 0.05 m.With active moisture transport, the TEEE membrane ensures an extremely fast drying capacity, which provides the membrane with the best possible protection against ice formation in winter.Once ice has formed, diffusion-open wall formwork membranes turn into vapour barriers (ice is diffusion-tight) and then represent moisture traps.Other special features of the TEEE membrane are its reliable protection against wood impregnating agents (water droplets cannot penetrate the membrane, even with reduced surface tension, as there are no pores) and its particularly high heat stability (melting point polymer approx. 200 °C, PP approx. 140 °C). This heat stability gives the plastic extremely high ageing stability over decades.High performance for all requirementsThe functional film is securely protected between two robust, particularly tear-resistant protective and cover fleeces made of polypropylene - ideal for high loads when laying the sheets.The cover fleece is also water-repellent and offers optimum protection against moisture penetration. It protects the special film underneath from damage and UV radiation.The membranes are glare-free due to the black colouring of the outer cover fleece.The membrane can be exposed to the elements for up to 6 months.
Content: 75 Square metre (€5.03 / 1 Square metre)
€377.47*
Pro Clima, Tescon INVIS, black all-round adhesive tape for indoors and outdoors, roll 30 m, width 6 cm
AdvantagesSticks securely - even in damp conditions: waterproof SOLID adhesiveBecomes virtually invisible: black backing fleece not visible behind gap formworkHolds reliably in the long term: UV-stable behind gap formworkMore flexible further work: 6 months freely weatherableEasy to apply: Fleece backing very pliable and can be torn off by handFaster further work: Fleece backing can be plastered over directlyStandard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2Best values in the pollutant test, tested in accordance with AgBB / ISO 16000Product information Processing instructionsApplicationExterior: Creation of windtightness of wall formwork membranes with pro clima SOLITEX FRONTA family as well as sarking and underlay membranes. Windtight bonding of wood-based panels as underlay. Airtight bonding of on-roof and renovation vapour barriers and airtight membranes.Indoors: Airtight bonding of vapour barriers and airtight membranes as well as airtight wood-based panels.All interior and exterior bonding can be carried out both to each other and to neighbouring smooth, non-mineral components (e.g. pipe penetrations, skylights).Division of the separating film forWidth 100 mm: 50 / 50 mmWidth 150 mm: 75 / 75 mmGeneral conditionsBonds must not be subjected to tensile loads.After bonding the sheets, battens must support the weight of the insulation material. Secure bonding with battens if necessary.Rub the adhesive tapes down firmly. Ensure sufficient counter pressure.Windproof, airtight or rainproof bonding can only be achieved on vapour control layers or sarking and façade membranes laid without folds.Quickly dissipate increased room humidity by consistent and constant ventilation, if necessary set up a building dryer.When plastering, please follow the recommendations of the plaster manufacturer for non-absorbent substrates. A bonding bridge may be required.SubstratesClean substrates before bonding. Bonding is not possible on frozen substrates. There must be no repellent substances on the materials to be bonded (e.g. grease or silicone). Substrates must be sufficiently dry and stable. Permanent bonding is achieved on all pro clima interior and exterior membranes, other vapour control layers and airtight membranes (e.g. made of PE, PA, PP and aluminium) or sarking/sarking membranes and wall formwork membranes (e.g. made of PP and PET). Bonding and connections can be made on planed and painted wood, hard plastics or metal (e.g. pipes, windows, etc.), hard wood-based panels (chipboard, OSB and BFU, MDF and wood fibre underlay boards). Pre-treatment with TESCON PRIMER is required when bonding wood fibre underlay boards or on smooth, mineral substrates. Concrete or plaster substrates must not sand.The best results for the safety of the construction are achieved on high-quality substrates. You are responsible for checking the suitability of the substrate; test bonding may be recommended. Pre-treatment with TESCON PRIMER is recommended for non-load-bearing substrates.
Content: 30 Linear metre (€1.11 / 1 Linear metre)
€33.29*
Pro Clima, TESCON PRIMER Solvent-free primer for indoors and outdoors, can 400 ml
For preparing or strengthening the substrate for subsequent bonding with pro Clima adhesive tapes, such as TESCON VANA, TESCON PROFECT and adhesive tapes from the EXTOSEAL family. Suitable for wood, wood fibre boards, masonry, roofs, walls and floor slabs.AdvantagesEasy to use - spray on directly from the can, no contamination of the primer in the containerSecure bonds: Penetrates deeply and consolidates non-load-bearing or dusty substratesSaves time: Adhesive tapes can be applied to absorbent substrates without drying timeFlexible use: Use on dry and slightly damp substratesAt any time of year: Can also be applied in frosty conditionsData sheet Processing instructions Safety data sheetGeneral conditionsShake can well before use.The fan-shaped spray jet can be adjusted horizontally and vertically by turning the spray head nozzle.After each spraying process, spray upside down until only propellant emerges so that neither the valve riser nor the spray head are clogged with primer residue. Wipe off primer at the nozzle outlet.After cleaning, spray the surface to be bonded - spray at a distance of 20 - 25 cm. Allow to evaporate for between 5 and 15 minutes (depending on the material and application). Repeat the process for absorbent substrates.Consumption valuesDelivery form Content Application width CoverageCan 0.4 l 60 mm approx. 38 m 75 mm approx. 31 m 150 mm approx. 17mAdvantagesSecure connections: Penetrates deeply and consolidates non-load-bearing or dusty substratesSaves time: No drying required for absorbent substratesWork more freely: Use on dry and slightly damp substratesCan be applied and distributed with just one hand thanks to the dispenser bottleCan be used at any time of year: Can also be applied in frosty conditionsBest values in the pollutant test, tested according to AgBB / ISO 16000, solvent-freeSubstratesClean substrates before applying primer.Surfaces that are frozen over or soaked through are unsuitable for primer application. There must be no repellent substances on the substrate (e.g. greases or silicones).All mineral surfaces (e.g. plaster or concrete) and (old) wooden substrates can be primed. It is also possible to consolidate porous materials such as wood fibre underlay boards.Absorbent substrates that are open to diffusion (e.g. wood fibre underlay boards) may be slightly damp. The respective adhesive tape can be applied directly to the still damp primer. The final strength is only achieved when dry. If necessary, securing measures, e.g. covering, are recommended. The primer, which is not yet completely dry, must be protected from the weather.If diffusion-inhibiting butyl rubber tapes (e.g. EXTOSEAL family) are applied to relatively dense, non-absorbent substrates (e.g. concrete), the primer must first be allowed to dry through before the adhesive tape is applied.Only ORCON CLASSIC or ORCON MULTIBOND can be used as a primer for connecting adhesives. Primer and ORCON CLASSIC must be completely dry (1-2 days) before the membrane material is applied.General conditionsShake or stir the can well before use. Approx. 4.5 m² of surface can be treated with one litre of primer.For particularly quick and easy application, insert the 1-litre dispenser bottle into the TENAPP application tool.Advantages: Application and distribution in just one operation with just one hand and no soiling of the primer in the container.
Content: 0.4 Litre (€32.45 / 1 Litre)
€12.98*
Pro Clima, TESCON VANA all-round adhesive tape for indoors and outdoors, roll 30 m, width 6 cm
AdvantagesSticks securely - even in damp conditions: waterproof SOLID adhesiveParticularly durable: 100 years of adhesive strength independently tested and confirmedContinue working more flexibly: can be freely weathered for 6 monthsContinue working faster: Fleece backing can be plastered over directlyEasy to process: Fleece backing is very pliable and can be torn off by handTest winner at Stiftung Warentest 4/2012Standard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2Best values in the pollutant test, test carried out in accordance with AgBB / ISO 16000Data sheet Processing instructions 100 years of adhesive strength ApplicationIndoors: Airtight bonding of vapour barriers and airtight membranes as well as airtight wood-based panels.Exterior: Ensuring wind and rain tightness of sarking, sarking and wall formwork membranes (e.g. pro clima SOLITEX) and sarking panels.Airtight bonding of on-roof and renovation vapour barriers and airtight membranes.All interior and exterior bonding can be carried out both to each other and to neighbouring smooth, non-mineral components (e.g. pipe penetrations, skylights).General conditionsBonds must not be subjected to tensile loads.After bonding membranes, battens must support the weight of the insulation material. Secure bonded joints with battens if necessary.Rub adhesive tapes down firmly. Ensure sufficient counter pressure. Windproof, airtight or rainproof bonds can only be achieved on vapour control layers or sarking and façade membranes laid without folds. Quickly dissipate increased room humidity by consistent and constant ventilation, if necessary set up a building dryer.When plastering, please follow the recommendations of the plaster manufacturer for non-absorbent substrates. A bonding bridge may be required.SubstratesClean substrates before bonding.Bonding is not possible on frozen substrates. There must be no repellent substances on the materials to be bonded (e.g. grease or silicone). Substrates must be sufficiently dry and stable. Permanent bonding is achieved on all pro clima interior and exterior membranes, other vapour barrier and airtight membranes (e.g. made of PE, PA, PP and aluminium) or sarking/sarking membranes and wall formwork membranes (e.g. made of PP and PET).Bonding and connections can be made on planed and painted wood, hard plastics or metal (e.g. pipes, windows, etc.), hard wood-based panels (chipboard, OSB and BFU, MDF and wood fibre underlay boards).Pre-treatment with TESCON PRIMER is required when bonding wood fibre underlay boards or on smooth, mineral substrates. Concrete or plaster substrates must not sand.The best results for the safety of the construction are achieved on high-quality substrates.You are responsible for checking the suitability of the substrate; test bonding may be recommended.Pre-treatment with TESCON PRIMER is recommended for non-load-bearing substrates.
Content: 30 Linear metre (€0.94 / 1 Linear metre)
€28.24*
TESCON No.1 all-round adhesive tape with carrier made of perforated PE film, for indoors and outdoors, roll 30 m, width 6 cm
AdvantagesSticks securely - even in damp conditions: waterproof SOLID adhesive !!!!!!Particularly durable: 100 years of adhesive strength independently tested and confirmedEasy to apply: Flexible backing, can be torn off by handAlso for penetrations: Very elastic and permanently mouldableFaster further work: Can be plastered over directlyStandard-compliant construction: For airtight connections in accordance with DIN 4108-7, SIA 180 and OENORM B 8110-2Best values in the pollutant test, test carried out according to AgBB / ISO 16000Data sheet Processing instructions 100-year adhesive strengthApplicationIndoors: Airtight bonding of vapour barriers and airtight membranes as well as airtight wood-based panels.Exterior: Airtight bonding of on-roof and renovation vapour retarders and airtight membranes. Creating the windtightness of sarking, underlay and wall formwork membranes (e.g. pro clima SOLITEX). Windproof bonding of wood-based panels for underlay.All interior and exterior bonding can be carried out both to each other and to neighbouring smooth, non-mineral components (e.g. pipe penetrations, skylights).General conditionsBonds must not be subjected to tensile loads. After bonding membranes, battens must support the weight of the insulation material. Secure bonded joints with battens if necessary.Rub adhesive tapes down firmly. Ensure sufficient counter pressure. Windproof, airtight or rainproof bonding can only be achieved on vapour control layers or underlay and façade membranes laid without folds. Quickly dissipate increased room humidity by consistent and constant ventilation, if necessary set up a building dryer.When plastering, please follow the recommendations of the plaster manufacturer for non-absorbent substrates. A bonding bridge may be required.SubstratesClean substrates before bonding.Bonding is not possible on frozen substrates. There must be no repellent substances on the materials to be bonded (e.g. grease or silicone). Substrates must be sufficiently dry and stable. Permanent bonding is achieved on all pro clima interior and exterior membranes, other vapour barrier and airtight membranes (e.g. made of PE, PA, PP and aluminium) or sarking/sarking membranes and wall formwork membranes (e.g. made of PP and PET).Bonding and connections can be made on planed and painted wood, hard plastics or metal (e.g. pipes, windows, etc.), hard wood-based panels (chipboard, OSB and BFU, MDF and wood fibre underlay boards).Pre-treatment with TESCON PRIMER is required when bonding wood fibre underlay boards or on smooth, mineral substrates. Concrete or plaster substrates must not sand.The best results for the safety of the construction are achieved on high-quality substrates.You are responsible for checking the suitability of the substrate; test bonding may be recommended.Pre-treatment with TESCON PRIMER is recommended for non-load-bearing substrates.
Content: 30 Linear metre (€0.92 / 1 Linear metre)
€27.70*
Manufacturer
Acoustics & Indoor Climate
Yosima – Medium-textured clay plaster
AMPACK Building Sealing
Content: 0.5 Litre (€37.60 / 1 Litre)
€18.80*
Content: 5 Linear metre (€4.17 / 1 Linear metre)
€20.87*
Content: 25 Linear metre (€2.34 / 1 Linear metre)
€58.43*
Content: 25 Linear metre (€2.59 / 1 Linear metre)
€64.80*
Content: 12 Linear metre (€0.57 / 1 Linear metre)
€6.78*
Content: 0.31 Litre (€30.29 / 1 Litre)
€9.39*
Content: 8 Linear metre (€1.60 / 1 Linear metre)
€12.82*
Content: 20 Linear metre (€5.66 / 1 Linear metre)
€113.29*
Content: 25 Linear metre (€1.25 / 1 Linear metre)
€31.33*
Content: 40 Linear metre (€1.21 / 1 Linear metre)
€48.25*
Content: 25 Linear metre (€1.83 / 1 Linear metre)
€45.71*
Content: 25 Linear metre (€1.75 / 1 Linear metre)
€43.83*
Content: 25 Linear metre (€0.86 / 1 Linear metre)
€21.44*
Content: 25 Linear metre (€1.27 / 1 Linear metre)
€31.81*
Content: 30 Linear metre (€0.73 / 1 Linear metre)
€21.91*
Content: 37.5 Square metre (€2.58 / 1 Square metre)
€96.59*
Content: 75 Square metre (€2.97 / 1 Square metre)
€223.01*
Content: 75 Square metre (€3.29 / 1 Square metre)
€246.60*
Content: 75 Square metre (€2.37 / 1 Square metre)
€177.39*
Content: 75 Square metre (€3.08 / 1 Square metre)
€231.07*
Content: 75 Square metre (€3.52 / 1 Square metre)
€264.00*
Content: 75 Square metre (€4.92 / 1 Square metre)
€368.98*
Content: 62.5 Square metre (€1.50 / 1 Square metre)
€93.70*
Content: 75 Square metre (€2.47 / 1 Square metre)
€185.12*
Content: 75 Square metre (€2.05 / 1 Square metre)
€153.43*