Kreidezeit wood stain for indoors and outdoors, colourless
Kreidezeit
Regular price:
€45.80
Content:
2.5 Litre
(€18.32 / 1 Litre)
Available, delivery time: 2-5 days
Product number:
11-321
Product information "Kreidezeit wood stain for indoors and outdoors, colourless"
Kreidezeit Wood Glaze offers a simple way to protect both indoor and outdoor surfaces from UV radiation, greying and the elements. This is a vapour-permeable and biocide-free protective coating that can be applied in a variety of ways to wooden surfaces. These may include, for example, windows, doors, timber façades, half-timbered structures, playground equipment, carports and similar items. The advantage of Kreidezeit Wood Glaze over other commercially available products of this type is that it does not flake, crack or split, but gradually weathers away over time. The effort required to renew it remains comparatively low, as it can be simply cleaned and repainted.
For external use, lightfast pigments should be added to the wood glaze to aesthetically enhance the natural wood grain. In contrast, the wood glaze can be applied colourless for internal use.
Kreidezeit Wood Glaze is unsuitable for floors, on rough-sawn timber, on existing synthetic resin-based coatings, and on horizontal surfaces outdoors.
Properties
Dirt- and water-repellent
does not crack, split or flake
weather-resistant and elastic
Transparent, glossy, enhances the wood grain
Vapour-permeable
easy to maintain
saliva- and sweat-resistant in accordance with DIN 53160
contains solvents (natural balsam turpentine oil)
free from biocides
free from cobalt, lead and barium
vegan
Colouring / UV protection
For interior use, the wood glaze can be applied either colourless or pigmented. For effective UV protection outdoors, the glaze must be tinted with pigments. Minimum pigment contents must be observed; see the colour chart for oil-based
pigments
pigments
Full declaration
Linseed oil, wood oil stand oil, linseed oil stand oil, balsam turpentine oil, rosin glycerine ester, manganese and calcium drying agents
Surface preparation / initial sanding
Remove resin blisters and old synthetic resin-based coatings. For external use: saturate absorbent cut edges and end-grain areas with Kreidezeit Resin Oil and allow to dry for at least 24 hours.
Sand new and weathered timber (grain size P 80–100) and round off the edges. Do not sand any finer, as this will compact the wood and prevent it from absorbing sufficient oil. It is better to ‘open up’ new, smooth, planed or finely pre-sanded timber by sanding. Remove all dust thoroughly after sanding.
Priming
Do not prime new or normally absorbent woods. Only prime highly absorbent or weathered woods with Kreidezeit Priming Oil.
Application
Shake the product briefly before use. On untreated wood, apply the wood stain at least twice, allowing the surface to dry between coats. Light sanding may be necessary before the second coat.
Mix containers from different batch numbers together before use. The product must not be poured onto surfaces!
Clean and dust untreated substrates. Kreidezeit Wood Glaze is applied undiluted.
Please note: Timber used outdoors should be fitted with stainless steel screws and fittings; otherwise, dark discolouration may occur when the surface is treated with oil.
Application and drying temperature: at least 10 °C for at least 48 hours.
1. First coat
Outdoors: Apply the pigmented wood glaze evenly with a brush or paint pad. Avoid excess glaze or smooth it out. If glaze has pooled, brush it out of corners with a clean brush. Stir the pigmented wood glaze before and occasionally during application.
Indoors: Apply in the same way as outdoors, using either the pigmented or colourless version. Alternatively, and provided a glossy finish is not desired, 10–20 minutes after application, rub the entire treated surface with a dry, lint-free cloth until any wood stain that has not been absorbed is completely removed and the surface has an even, silk-matt finish.
2. Intermediate sanding (optional)
Intermediate sanding is only necessary if the surface has dried rough after the first coat, e.g. due to raised wood fibres. Sand with sanding fleece in the direction of the grain.
Dust thoroughly after sanding.
3. Final coat(s)
Repeat the process as for the first coat.
Particularly when used outdoors, it is important that the surfaces are well saturated upon completion and have an even, silky-gloss finish. To achieve this, further coats of wood stain may be necessary.
Drying time
Dry and ready for further work at 20 °C and 60 % relative humidity after approx. 24 hours; on tannin-containing substrates (oak, etc.) after at least 48 hours.
High humidity, cold temperatures and tannin-containing substrates significantly prolong the drying time. Fully cured after approx. 4 weeks.
Suitable tools
Varnish brushes and paint pads. Do not spray or roll the product.
Cleaning the tools
Wash immediately after use with balsam turpentine oil, then rinse with olive care soap or Corfu soap.
For interior use, the wood stain can be applied either colourless or pigmented.
For external use, the following minimum pigment contents must be observed:
at least 15 %: (150 g/l) golden ochre, yellow ochre, red ochre, orange ochre, red sienna, fawn umber, reddish umber, reddish-brown umber, dark greenish umber, dark umber, green umber
at least 10 %: (100 g/l) spinel yellow, orange, green, turquoise, blue, mint, sun yellow, oxide orange
min. 8 %: (80 g/l) Iron oxide black
Ultramarine blue and violet are unsuitable for outdoor use. We advise against using glazing tints with titanium white outdoors due to insufficient UV protection.
To tint the paint, first mix the pigments with a small amount of glaze to form a lump-free paste, and only then stir them into the colourless glaze. The pigments can be mixed together as desired. Instructions.
Alternatively, the wood glaze can be tinted in any proportion with stand oil paint; for outdoor use, add at least 30 per cent by volume.
| Areas of application: | Substrate preparation / priming, Wall coating |
|---|---|
| Manufacturer: | Kreidezeit |
| Packaging: | Canister, Tin |
| Pack size: | 5 litres, 10 litres, Canister 5 litres, Tin 0.75 l |
| Product category: | Accessories, Paints/Plasters, Window products |
| Product group: | Paints and primers, Window products |
| Product line: | Kreidezeit wood glaze |
| Shipping: | Collection available, Parcel shipping |
Login
No reviews found. Share your insights with others.